• ESUN 3D Filament  ABS 1.75mm 1KG
    Availablity

    3 in stock

    Product Parameters: 1.75mm Characteristics: Non harmful,non-toxic,and environment friendly. Good material toughness,good strength. Suitable for complex models. Low material shrinkage rate,uniform diameter. Printing temp. is 190~220℃,lower than other materials. Package Included: ESUN 3D Filament ABS 1.75mm 1KG
  • ESUN 3D Filament  ABS 2.85mm 1KG
    Availablity

    Out of stock

    Product Parameters: 2.85mm Characteristics: Non harmful,non-toxic,and environment friendly. Good material toughness,good strength. Suitable for complex models. Low material shrinkage rate,uniform diameter. Printing temp. is 190~220℃,lower than other materials. Package Included: ESUN 3D Filament ABS 2.85mm 1KG
  • Availablity

    3 in stock

    Product Parameters: 2.85mm Characteristics: Non harmful,non-toxic,and environment friendly. Good material toughness,good strength. Suitable for complex models. Low material shrinkage rate,uniform diameter. Printing temp. is 190~220℃,lower than other materials. Package Included: ESUN 3D Filament PLA 2.85mm 1KG
  • ESUN 3D Filament  PLA 1.75mm 1KG
    Availablity

    5 in stock

    Product Parameters: 1.75mm Characteristics: Non harmful,non-toxic,and environment friendly. Good material toughness,good strength. Suitable for complex models. Low material shrinkage rate,uniform diameter. Printing temp. is 190~220℃,lower than other materials. Package Included: ESUN 3D Filament PLA 1.75mm 1KG
  • E3D V6 J-head Hotend Extruder Nozzle Kit Cooling Fan
    Availablity

    3 in stock

    Product Parameters: Product Model: V6 for E3D Nozzle Size: 0.4mm for 1.75mm Fliament. Thermistor: 100K, NTC 3950, 1 meter Length Heater wire: 12V 40W, 1meter Length Teflon tube: 1 meter ,Bore ID4mm OD6mm , Cooling Fan: 30*30*10mm ,12V, with 2 Pin wire and bracket. The size about 3D V6 Heat…
  • Diameter OD 16mm x 500mm Cylinder Liner Rail Linear Shaft Optical Axis
    Availablity

    8 in stock

    Product Parameters: Material: bearing steal,GCr15 Hardness: About  HRC58° Precision: g6 Surface roughness: Below 1.5μM(Rmax) Surface hard-thickness: 0.8μ~3mm Outer diameter: 16mm Length: 500mm  Staightness: Below 5μM/100mm Hard chrome thickness: 3.0μM(Rmax) Package Included: 1PCS Diameter OD 16mm x 500mm 
  • 3D Printer Controller Board For Ramps 1.4 Reprap Prusa Mendel Arduino
    Availablity

    5 in stock

    Product Parameters: Brand new and high quality. Fully assembled & tested, no soldering required. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. Specification: Size: 11.5cm x 6cm / approx. 4.5in x 2.4in. Package Included: 1PCS 3D Printer Controller Board For Ramps 1.4 Reprap Prusa Mendel Arduino 
  • 3D Printer CNC V3 Engraver Shield Expansion Board
    Availablity

    10 in stock

    Product introduction The expansion board can be used as engraving machine, 3D printer and other drive expansion board, a total of 4 stepper motor drive module slot, (Note that this board does not contain A4988 stepper motor drive module, you need to shop in the shop) , Can drive 4 road…