-
$3.50L293D Motor Driver Module Board DC 4.5V – 16V Shield For Arduino Items Description L293D is a monolithic integrated, high voltage, high current, 4-channel driver.Basically this means using this chip you can use DC motors and power supplies of up to 36 Volts, thats some pretty big motors and the […]
-
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$1.25 – $4.00Copper Clad Sheet PCB Laminate DIY Circuit Board PCB Single A4 A5 PCB Double A4 A5
Select options This product has multiple variants. The options may be chosen on the product page -
$4.00Description: Water flow sensor consists of a plastic valve bodya water rotorand a hall-effect sensor. When water flows through the rotorrotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse signal. This one is suitable to detect flow in water dispenser or coffee […]
-
$3.00Microcontroller based on the AVR RISC architecture. Max CPU operating frequency: 16MHz Flash: 16kB RAM: 1kB EEPROM: 512B Features * Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes * One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode * Real Time Counter with Separate Oscillator * Four […]
-
-
$2.50The MQ-5 Gas Sensor module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. Sensitive for LPG, natural gas, coal gas Output voltage […]
-
$2.50he ATmega8A is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8A achieves throughputs approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed. Features High-performance, Low-power AVR® 8-bit Microcontroller Advanced […]
-
$3.50DRV8825 Step Stick Stepper Motor Driver Module Breakout with Heat Shrink for CNC and 3D Printer
-
Out of Stock
$5.00The LilyPad Arduino is designed for e-textiles and wearables projects. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread.
-
-
-
$1.50Items Description Digital Light intensity detection module: GY-30 The ROHM genuine BH1750FVI chip Power supply :3-5v Illumination range :0-65535 lx The sensor built 16bitAD converter Direct digital output, complex calculation is omitted, omitting calibration Does not distinguish between ambient light Close to the visual sensitivity of the spectral characteristics 1 […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.13 – $0.50Red DIP Switches 2.54mm
Select options This product has multiple variants. The options may be chosen on the product page -
$2.50MQ-4 Gas Sensor Module detects the presence of methane (CNG) gas at concentrations from 300 ppm to 10,000 ppm, a range suitable for detecting gas leaks. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller. Specifications : Power requirements : VCC – 5V±0.1 DO […]
-
-
$1.50KY-026 Flame Sensor Module Detects Infrared Light Emitted KY-026 module is ideally suited to light detection within the range of 760 – 1100nm, typically seen in project robots and flame detection systems. The analog signal pin provides an analog output based on the level of radiation available to the sensor. […]
-
-
Concept
Bridge Cable Robot
Cable Inspection Robot is a research project by ArrowDot Company with function to check the quality of cable for bridge which can be used for Neak Loeung Bridge, New Balay Bridge and planned Koh Pich-Koh Norea Bridge. This robot equipped with analyzed camera that can view the cracked point and the vibration level of the cable. Last but not least, this robot can be remote and live up to 500m wirelessly.
