-
-
-
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$1.50 – $3.501 Pair APC Propeller For Fixed Wing Nylon Propeller Multi-Copter Slow Flyer RC Aircraft
Select options This product has multiple variants. The options may be chosen on the product page -
Select options This product has multiple variants. The options may be chosen on the product page Quick View$6.00 – $8.50Arduino Uno is a microcontroller board based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator (CSTCE16M0V53-R0), a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.. You can tinker with your Uno without worrying too much about doing something wrong, worst case scenario you can replace the chip for a few dollars and start over again.
Select options This product has multiple variants. The options may be chosen on the product page -
$4.50USB 2.0 to TTL RS485 Serial Converter Adapter FTID FT323RL USB 485 Modules FT232 Chips
-
-
$4.00WS2811 and WS2812B Remote Control 21 Channels 5-24V IR Remote + Receiver Include Battery CR2025
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.75Blue Aluminum Coupling Shaft Connect L25 W14
Select options This product has multiple variants. The options may be chosen on the product page -
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.38Mini DC Brush Motor 130 Low Torqe DC 3-6V
Select options This product has multiple variants. The options may be chosen on the product page -
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.19 – $1.03PH 2.0mm Wire Cable Connector Single Head Female 10CM
Select options This product has multiple variants. The options may be chosen on the product page -
$35.00Component features: Supply voltage: 20 – 50 VDC Output current: 0.5 – 5.6 A Pulse input frequency up to 200 kHz Automatic idle-current reduction Supports PUL/DIR and CW/CCW modes Extra-low motor noise offers excellent quietness Anti-Resonance, provides optimum torque and nulls mid-range instability Self-test and Auto-configuration technology, offers optimum responses […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.30Potentiometer Linear WH148 15mm
Select options This product has multiple variants. The options may be chosen on the product page -
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.75PTFE Tube Push Pneumatic Connector
Select options This product has multiple variants. The options may be chosen on the product page -
$2.50he ATmega8A is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8A achieves throughputs approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed. Features High-performance, Low-power AVR® 8-bit Microcontroller Advanced […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$3.00A4988 Step Stick Stepper Motor Driver Module with Heat Shrink for CNC and 3D Printer
Select options This product has multiple variants. The options may be chosen on the product page -
Out of Stock
$23.00The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.
-
Concept
Bridge Cable Robot
Cable Inspection Robot is a research project by ArrowDot Company with function to check the quality of cable for bridge which can be used for Neak Loeung Bridge, New Balay Bridge and planned Koh Pich-Koh Norea Bridge. This robot equipped with analyzed camera that can view the cracked point and the vibration level of the cable. Last but not least, this robot can be remote and live up to 500m wirelessly.
