-
$6.00Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5 The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily,what’s more ,Ramps 1.6 have a good Heatsink above MOS […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$1.25 – $2.50GT3 Rubber Timing Belt Close Loop Width 10mm
Select options This product has multiple variants. The options may be chosen on the product page -
-
$7.00MAX6675 Module Thermocouple Sensor This MAX6675 Module K Type Thermocouple Sensor Measure 1024°C Temperature sensor makes use of the Maxim MAX6675 K-Thermocouple to digital converter IC to provide a microcontroller compatible digital serial interface (SPI compatible) for giving an accurate temperature compensated measurement of the supplied K-Type thermocouple sensor. It […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.25 – $0.60Extension Wire Cable 22AWG LED Strip Wire 2-6Pins
Select options This product has multiple variants. The options may be chosen on the product page -
-
-
$12.00GY-906-BCC MIX9014 ESF-BAA IR Infrared Temperature Sensor Range 2CM This is an infrared thermometer designed for non-contact temperature sensing. An internal 17-bit ADC and a powerful DSP contribute to the MLX90614’s high accuracy and resolution. It has a huge number of applications including body temperature measurment and movement detection. The […]
-
$3.00HX711 Module Load Cell Voltage Amplifier HX711 features dual-channel 24 Bit Precision A/D Weight Pressure Sensor Load Cell Amplifier which is available in a small breakout board. The board has pinouts for the microcontroller and the Load cell in two different directions for the ease of interfacing. It can be […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$1.00 – $11.80Select options This product has multiple variants. The options may be chosen on the product page -
-
-
$1.00Glyduino SW-1801P Vibration Sensor Switch Alarm Specification: High sensitivity vibration switch by SW-18010P vibration sensors . The comparator output signal with good waveform ,driving ability , more than 15mA Working voltage: 3.3V-5V Output format : digital switching outputs ( 0 and 1 ) With M3 holes, Easy installation PCB board […]
-
$1.50KY-026 Flame Sensor Module Detects Infrared Light Emitted KY-026 module is ideally suited to light detection within the range of 760 – 1100nm, typically seen in project robots and flame detection systems. The analog signal pin provides an analog output based on the level of radiation available to the sensor. […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.20 – $1.15AA Battery Box Holder
Select options This product has multiple variants. The options may be chosen on the product page -
-19% Off
Original price was: $43.00.$35.00Current price is: $35.00.Spot Welder Handheld Quick Release Pen
-
$3.50Mini PIR Motion Sensor Module This motion sensor is a mini version of the standard PIR sensor that we sell. This type of sensor can be used to detect movement by means of infrared light. Input Voltage: DC 2.7-12V Quiescent current: <100uA Level output: High 3.3 V/Low 0V Delay time: […]
-
$5.00Specifications: Product: PWM Signal Generator Model: XY-PWM Operating Voltage: DC 3.3V-30V Frequency Range: 1Hz~150KHz Frequency Accuracy: ±2% Duty Cycle Range: 0.00% – 100% Output Current: Approximately 5-30mA Output Amplitude: Corresponds to Input Voltage Dimensions: 79 x 43 x 27mm Operating Temperature: -20°C~70°C
-
$7.00Product Introduction: 1.Name:numerical control battery charging control module 2.Model:XH-M602 3.Input Voltage:AC 220V 4.Display Precision:0.1V 5.Control Precision:0.1V 6.Output Type:output switch 7.Voltage Tolerance:+/-0.1V 8.Application Fields:for 3.7-120V lithium battery or storage battery 9.Size:86*58*24mm
Concept
Bridge Cable Robot
Cable Inspection Robot is a research project by ArrowDot Company with function to check the quality of cable for bridge which can be used for Neak Loeung Bridge, New Balay Bridge and planned Koh Pich-Koh Norea Bridge. This robot equipped with analyzed camera that can view the cracked point and the vibration level of the cable. Last but not least, this robot can be remote and live up to 500m wirelessly.
