-
$3.00Open-builds V Gantry Plate 2020 V-Slot Aluminum Profile Slider Plate No Wheel CNC Part 3D Printer Wheel Roller
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.19 – $1.03JST 1.25mm Wire Cable Connector Single Head Female 10CM
Select options This product has multiple variants. The options may be chosen on the product page -
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.30 – $0.60JST SM Plug Male to Female Wire Cable Connector
Select options This product has multiple variants. The options may be chosen on the product page -
$2.50Micro USB input: 5V 1A USB Output: 5V 2.1A / 5V 1A(Dual USB interface) Charging display: intelligent digital display Batteries Type: liquid lithium-ion batteries (18650) Product Size: 57mm x 28mm Screen size:27mm x 17mm
-
-
-
$4.25Specification: Clock speed: 16 MHz Flash memory: 32 KB 32 line output/input The JTAG interface Two 8-bit Counters One 16-bit counter Four channel PWM 8 channels 10-bit Converter analog-to-digital Hardware network interfaces: USART, SPI Six sleep modes Power Requirements: 2.7 V – 5.5 V Case DIP40
-
- 18 % Off Select options This product has multiple variants. The options may be chosen on the product page Quick ViewOriginal price was: $2.75.$2.25Current price is: $2.25.TT Gear Motor DC 3-6V Medium Torque 160RPM T Shape Plastic Gear
Select options This product has multiple variants. The options may be chosen on the product page -
-
$7.50Items Description Model: HC-08 Working frequency band: 2.4G Communication interface: UART3.3VTTL level Working voltage: 2.0 ~ 3.6v RSSI support: not supported Communication level: 3.3v Transmit power: 4dBm (max) Transmission distance: 80 meters Emission current: 31.6mA Module size: 26.9 * 13mm Air speed: 1Mbps Antenna interface: built-in PCB antenna Sleep current: […]
-
$20.00Items Description Three power input interface: DC044 interface and V_IN and a lithium battery interface. Note that: The range of DC044 and the V_IN pin voltage input is 5 – 26V, when use the 5V as the power, be sure that the power supply can provide 2A current. The range […]
-
$5.70INA219 DC Current Sensor Module Breakout Board I2C 26V 1. The programmable calibration register can be read in amps of DC and power in watts. 2. Up to 128 samples can be averaged to achieve filtering in a noisy environment. 3. The I2C interface has a timeout setting, which can […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$18.00 – $30.00Infinity Li-Po 4S 14.8V with XT30 Battery Connector
Select options This product has multiple variants. The options may be chosen on the product page -
-
Out of Stock
$5.00The LilyPad Arduino is designed for e-textiles and wearables projects. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread.
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.30 – $0.70M5 Hammer Head T-Bolt Slid (5pcs)
Select options This product has multiple variants. The options may be chosen on the product page -
$1.00Glyduino SW-1801P Vibration Sensor Switch Alarm Specification: High sensitivity vibration switch by SW-18010P vibration sensors . The comparator output signal with good waveform ,driving ability , more than 15mA Working voltage: 3.3V-5V Output format : digital switching outputs ( 0 and 1 ) With M3 holes, Easy installation PCB board […]
-
$8.50Description Doit ESP32 Development board is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters, and power management module. The entire solution takes up the least amount of printed circuit board area. This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low […]
-
Select options This product has multiple variants. The options may be chosen on the product page Quick View$0.20 – $0.38IC 555 Timer IC PC817 IC MOC3021 IC 4N25
Select options This product has multiple variants. The options may be chosen on the product page
Concept
Bridge Cable Robot
Cable Inspection Robot is a research project by ArrowDot Company with function to check the quality of cable for bridge which can be used for Neak Loeung Bridge, New Balay Bridge and planned Koh Pich-Koh Norea Bridge. This robot equipped with analyzed camera that can view the cracked point and the vibration level of the cable. Last but not least, this robot can be remote and live up to 500m wirelessly.
